Lasted edited by Andrew Munsey, updated on June 14, 2016 at 9:09 pm.
Pure Energy Systems News
January 6, 2010
This has to be the simplest free energy design I've ever encountered. I can't fathom anything being any simpler than this. Does it work?
According to David McNutt, who contacted me yesterday to tell met about this, "it works". And he's willing to open source the design. If it turns out to verify as a functional design, we ( and McNutt) have an agreement for sharing any revenues that might come from this (traffic, plans, kits, completed units, etc).
He built it a decade ago using ½-inch Styrofoam, a pencil for the shaft, and some 1/4x1/4-inch rod magnets (neodymium-iron-boron) he had kicking around from a game called mag-neticks. He used a hand drill to make equally-spaced holes around the perimeter of the approximately 4.5 to 5-inch diameter Styrofoam piece. He said it is important to not have the rotor magnet any further apart than the diameter of the magnet and on the other extreme, the rotor magnets must not be so close they touch.
The stator is comprised of a rod magnet of dimensions ¼" by 1-inch. He brings it into position by hand, coming in vertically along the tangent line, as the arrow on the right indicates.
: "Then keeping the drive rod … at [N] side toward the disk and at a 90 degree angle and in line so it is at the outside edge (but not touching). The closer you place the drive magnet the faster, and stronger the torque."
At the time he built this 8-10 years ago, he was living with a friend, Jerry Elswick, and wanted to prove that a generator could be made using just the power of magnets.
McNutt said he never got more than 3-4 revolutions before things fell apart, as the set-up was very crude. If the stator magnet got too close to the rotor, it pulled the magnet out.
I called Jerry, who said he's been friends with David for a couple of decades and yes he remembered the motor. He thought it had run maybe 200 revolutions for maybe 2-3 minutes. Jerry said David had been working on the idea for years and had it all worked out on paper, and claimed he could build a simple proof of concept design so Jerry gave him free run of his garage. David got some magnets from Wal-Mart "from some toy", and in maybe 2-3 days he had built the device.
Jerry called back saying that his wife, Betty, also remembers seeing it run. I talked to her on the phone as well. "I remember it was a pretty big thing back then," she said. She thinks it was more like 5-6 years ago. "They were working on it over a few weekends."
David said that after the Styrofoam version that he then fabricated a similar unit using square magnets, a bar magnet, wood and hot glue. He said this one started spinning so fast in the first fraction of a second that one of the magnets flew out from centripetal force and scared the dog.
That's all he's ever done with it, being a bit paranoid.
Now he would like to see it resurrected and scaled to replace the primary driver in power plants. The reason he called me was to see if I knew anyone who could replicate this.
: "I have changed to an arc magnet instead of the rod for the better field distribution in my next design. (But with no help funding for the machining it's been in limbo for a long time.)"
He agrees with me that a magnet motor does not violate core laws of physics but merely harnesses some yet-to-be-understood principle of nature. He has a theory about that.
It's simple enough to validate easily.
Wouldn't that be a hoot if this really worked! So close, and yet so far away – for all these decades. "Why didn't someone think of it sooner?" will be the most frequently asked question, followed by, "Why didn't McNutt do something with it before now?" Better late than never.
I talked him into letting us use his name in the motor name because it is so apropos for this "crackpot" stigma field.
Is it real? Let me know what you find, you replicators out there.
If it's a working design, I'd love to be able to announce it to the Event:2010:Top 10 Exotic Free Energy Technologies for Earth Transformation Conference conference I'm speaking at on Friday evening. We may be able to webcast that live. The more replications we can refer to, the better. This one could be just the ticket for breaking the logjam on free energy technologies.
This PESWiki page is the official destination for this open source project.
David & Tena's pending wedding, May 8, 2010.
Buying drill press in the morning and can start on next model.
This design was made as a proof of concept with what was available at the time.
It only shows the motion and thereby a weak effect is created.This is by no means the last in the design. To correct for the magnetic flux density on the rotor, substitute a Diamagnetic to obtain the consistency for the rotor. While this works it is not an effective design because of the lack of torque.
This is overcome in the later versions.
Saving for drill press and then I can start making a model.
I will use the same setup but four bar magnets to run it(stator).and four arc magnets for the rotor.
Drawing it up today.
Thanks Clanzer for the work btw all my fault for the lack of drawing.
Started making my ver.
On January 08, 2010 5:39 AM mountain, before commencing the work shown below, CLaNZeR wrote:
This most basic setup is what most people try when first playing with
magnets. I have tried multiple magnets on a rotor in the same config as
shown before and sorry to say it does not work.
I do not see how this will work, If he was holding the stator magnet and
it was not static, then we are back to the hand movement doing the work
and no free lunch.
Probably got a rotor knocking around that is suitable to show what I
mean, but I think it will be a waste of time.
Will see if I can get time later.
(YouTube January 08, 2010)
Note: This is a nice-looking piece of work however, CLaNZeR's spacing between rotor magnets is not as suggested by McNutt, who said they should not be any further apart than 1/2 the diameter of the rotor magnet, and they should not be touching. CLaNZeR's rotor magnets are at least 1 diameter distance apart. -- SilverThunder 10:52, 8 January 2010 (PST)
note by David:
Close, the reason it equalizes is because of the short stator magnet. Using that rotor I would estimate a 6" rod would be required to get rotation. If you notice the rotor stops at the S pole of the closest magnet segment(because there are three magnets each is a segment with separate fields.) The stator must have a length that places the center of the magnet in line with the incoming rotor magnet. Using the mid point as the attraction source should compensate for the magnet spacing.
Version 3 Rig Jan. 10, 2010.Latest /
There was an error working with the wiki: Code> Classifieds: Sean (CLaNZeR) Offering Custom CNC Milling Services - In response to my article, Career opportunities abound in free energy, master replicator, Sean (CLaNZeR) from the U.K. is putting out feelers to see about offering his professional services to build other people's prototypes or kits as a career. Let him know if you are one who would like to take him up on this, as he may be freed up in the next couple of months to start doing this. (PESWiki November 20, 2010)
The rotor spacing is great now just need to get more compression from the stator but the model im starting may make it more obvious what happens when the field is in line.
to get rotation the flux field between the stator and the rotor must be compressed by moving much closer as long as the south pole stays out of range it will repeat.
On January 07, 2010 8:45 AM Mountain, J.L. wrote:
Seems odd that one said it broke after a few revolutions and the other said it ran at 200 RPM for several minutes. Maybe they built several. What is described has never worked for me. Maybe I just do not understand.
: Response: No one said 200 rpm. They said "maybe 200 rotations". -- SilverThunder
And on Jan. 8, 2009, David McNutt wrote:
My main account is not working yet as this was a fast posting, so I made a temp contact email with firstname.lastname@example.org so I could post.
No, it was 200 turns or revolutions he guessed. He was estimating turns and the time he played with it.
The math for that estimation is faulty because at that calculated RPM the centrifugal force alone would have made the magnets come out of the foam. This was a friend who saw it run for a concept not a full practical model.
The magnetic field must be uniform around the rotor (the more uniform, the better the function of the rotor). The field determines the length of the driving magnet "stator" and such it's S pole MUST be out of the reach of the field from the rotor or it will equalize and therefore stop the motion so the best way to set it is so that when the rotor magnet comes in range of the magnetic field of the "stator" it MUST be past the mid point of the stator or the field can find a balance and therefore stops the turn/motion as can be seen by simply placing a small magnet at different center-points on a longer magnet. The reversing direction of said field must not be close to the rotor. You can extend the field by a longer stator or simply adding an iron rod/bar (magnetic material) to the end of the stator this will alter the field to allow a one way direction.
And yes I have made many changes to provide a much stronger and more stable magnetic field effect, that first model was only to show the concept not a final product (to clarify).
And thank you for the question. I hope I answered you appropriately.
David McNutt resides in the United States. He has other inventions to his name, some of which can't be disclosed due to NDAs, and others of which he's not ready to disclose yet. He's waiting to see how people handle this disclosure before he shares more.
by David McNutt co-written with Anne Olivia
Jan. 8, 2010
Basic science precepts teach that opposites attract and like poles repel in magnetic fields.
My theory extends this understanding of the characteristics of the magnetic fields' uses. In other words, if we are using a permanent magnet for it's magnetic field effect or, if you like, this shape of the field can be manipulated.
With a round permanent magnet you have a N and a S pole that are directly opposite each other. Thus, the magnetic field effect resembles the shape of the magnet. In order to achieve a differnt magnetic field, a magnet is used to incororate the desired effect. For further clarify, a rotor needs to have a circular magnetic field. To achieve the desired effect the external or exposed part of the magnet should be N, with the S being the internal pole.
For safety and efficacy reasons, it is preferable that these magnets are enclosed, due to the risk of the strong fields moving the magnet and effecting the balance of the rotor. Also it reduces the chance of a damaged magnet being thrown out of the rotor assembly, possibly injuring or damaging the mechanics of the motor or anyone within range. The magnets can shatter similar to schrapnel.
The "stator" magnet drives the rotor pushing by using the same N pole of as the outside of the rotor magnets.
The critical difference in this design is that the stator magnetic field effect is accomplished by assuring that the S pole is distant enought to have no effect of the rotor magnets. This maintains the pushing action of basic magnetic theory. It also results in the continous rotation of the motor. This reaction immediately spins the rotor at a high rate. In time, inertia will somewhat accelerate the rotation. However, this is relatively insignificant.
It is extremely important that the axle or shaft in the motor does not generate friction, thus resulting in instability of rotation or drag. This does not contradict any known science of magnetics. It simply manipulates the magnetic fields in a consistent manner, as well as lending it to new uses.
Feel free to view/post comments at our Examiner.com version of this story.
http://tech.groups.yahoo.com/group/McNuttMM/ - project forum, commenced Jan. 6, 2009
email: [mailto:McNutt@pureenergysystems.com?subject=McNutt%20Magnet%20Motor McNutt@pureenergysystems.com] – forwards to McNutt's email.
MAGNET MOTORS FOOTER
PowerPedia:Magnetic motor - encyclopedic entry
LEADING (including legendary status)
Directory:Disturbed Self-Compensating Symmetry (Terawatt Research)
There was an error working with the wiki: Code
There was an error working with the wiki: Code