Like us on Facebook and Follow us on Twitter


Directory:Pyrazo Device

Lasted edited by Andrew Munsey, updated on June 15, 2016 at 12:54 am.

  • 2 errors has been found on this page. Administrator will correct this soon.
  • This page has been imported from the old peswiki website. This message will be removed once updated.

Page first featured July 27, 2009

Image:Pyrazo circuit 300.gif

Inventor, David Robert Morgan, presents the Pyrazo circuit which is an electronic circuit that is designed to attract oscillations from an oscillation source. It does not create energy, but rather it absorbs energy.

It works by generating an extremely high voltage spike during the peaks of the oscillation cycle. This voltage spike is of a polarity that attracts the photons of the signal.

The device can also be connected to mechanical devices capable of converting oscillations of any type to electrical oscillations, such as speakers. When used with in combination with a speaker, it will draw in sounds from great distances. It generates a canceling wave and it can be used to eliminate unwanted sounds or radio signals.

: "Tesla's Pierce Arrow device and Moray's devices might no longer be lost to history! The bad news is that the plans are not for sale. The good news is that they are posted right on the [web]." -- David Morgan, July 26, 2009

Main Website

How the Device Works

The signal is routed through the primary of a transformer for the first quarter of the oscillation cycle until the first peak of the oscillation. At that point (pi/2 radians) the current through the primary is interrupted, which causes a voltage spike in the secondary due to the collapsing magnetic fields. The voltage spike of the secondary is shunted back to the antenna where it pulls the signal in the same direction that it is currently moving. In the full cycle version of the device, the process is repeated for the signal moving in the other direction.

Components of the Full Cycle Version
Image:Pyrazo circuit colored.GIF
Components of the Half Cycle Version
Image:Pyrazo hdcircuit colored.GIF
Animation of the Full Cycle Version
Image:Pyrazo circuit animation.gif

Note the positive feedback loop of the voltage spike being shunted through the primary.

Animation of the Half Cycle Version
Image:Pyrazo hdcircuit animation.gif
Tuner in Timer Variation of the Device

Thanks to the MIB for this variation. -) It may be necessary to isolate the tuner from the effect of the voltage spike. Beware the orientation of the tuner coil relative to the isolation transformer so that they are NOT mutually inductive.

Image:Pyrazo hdcircuit variation.GIF
Image:Pyrazo circuit variation.GIF

Design Tips

The values for the components will change depending on what signal source you are working with. The resistors and capacitor of the timing circuit (or inductor, switching I1 and I2) have to be tuned for the frequency you are targeting, otherwise it will not properly shift the frequency pi/2 radians. An oscilloscope is helpful in determining this. The transformers have to be choosen so that their self-resonant frequency is not near the target frequency. And the inductance of the tuning coil (if a tank circuit is used in the tuning circuit) should be much smaller than any coil or transformer in parallel to it to prevent them from skewing the resonant values. Also, with the signal, you will need a timing isolation transformer that allows the signal through with enough voltage and current to drive the switches. Depending on the target signal, you may have to bias the tubes. All manner of switches, including relays may be used. FETs should work as good as tubes. Relays would need diodes to accompany them and each switch would need to be connected to both sides of the timing circuit, because said circuit is decoupled. Bi-polar transistors may also be used, but would need to be surrounded with diodes so that the emitter can be attached to the other timing circuit output (I2 for I1, I1 for I2, P1 for P2, and P2 for P1) also because the timing circuit is decoupled. The simplest case may be an AM radio signal with FETs.

And some more design tips:

Unlike Moray, it won't work with with cold tubes. Moray's tubes contained radioactive elements and therefore did not need a heater element. While it is possible to obtained radioactive Krytrons, they are watched because of their use in triggers for the explosives used in the "fat man" style nuclear weapons and the process of obtaining them is a lengthy one. This is no problem, because hot cathode tubes can be used and the heaters can be powered from a car battery that will be replenished by the output of the device. Make sure that the voltage and amperage going into the heater elements matches the specifications for the tube that you choose to use.

The tubes should be rated for the frequency that you are trying to absorb. This information is commonly available on the internet in the specification for the tube type.

Choose an EM radiation source of a fixed frequency. Good sources are: 60Hz high voltage power lines (used by Tesla), AM radio stations (much to the FCC's chagrin), or a rich band of ionospheric vibration (used by Moray, 5.454 MHz if his 87' antenna is an indication, but there are many others.) Without a targeted energy source, the device will produce no energy. The device does not create or destroy energy, it merely transfers it.

If you are using audio transformers to capture 60Hz energy, be sure that they aren't designed to filter out that frequency. Some are.

Choose transformers that are capable of working with the frequency that you are targeting. (E.g. an audio transformer will not work for frequencies in the MHz range.)

Right on the other side of the timing circuit isolation transformer, you may have to protect whatever timing circuit you are using from the voltage spikes that come back from the pulse transformer. Two reversed biased zener diodes, facing opposite directions, and connected to each other on one side, and connected to each side of the secondary of the isolation transformer on the other side will work for this.

They should be arranged like this: T---|>Z----Z Pyrazo]

Image:Pyrazo device95x95.GIF
Latest: Directory:Radiant Energy > Directory:Power from Ambient Electromagnetic Radiation > Directory:Pyrazo Device - Inventor David Robert Morgan presents plans online for a technology having likeness to Tesla's Directory:Tesla's Pierce-Arrow and Directory:Thomas Henry Moray's devices which harvest radiant or oscillating energy freely from the environment, whether natural or man-made. The circuit also appears to have frequency and/or noise cancellation capabilities. (PESWiki July 27, 2009) (Comment)

Other Coverage

list here


See Talk:Directory:Pyrazo Device


David Robert Morgan

See also

Directory:Power from Ambient Electromagnetic Radiation

There was an error working with the wiki: Code[1]

There was an error working with the wiki: Code[2]

Directory:Radiant Energy



Directory:Best Exotic Clean Energy Technologies

News:Best Exotic Free Energy Technologies

Template:Tesla footer


Directory:Galactic Sea of Energy

There was an error working with the wiki: Code[1]

Directory:Atmospheric Electrostatic Energy

Directory:Dark Energy

There was an error working with the wiki: Code[2]


There was an error working with the wiki: Code[3]

There was an error working with the wiki: Code[4]

Directory:Electric Universe


Directory:Fractal Antennas as an Energy Source


Directory:Electromagnetic (overunity)

There was an error working with the wiki: Code[5] | News:2006-2008:Electromagnetic

Directory:Motor-Generator Self-Looped with Usable Energy Left Over

There was an error working with the wiki: Code[6]

Directory:Linear Magnet Accelerators

Directory:Pyramid Power

Directory:Quantum Particles

PowerPedia:Tunnel Magneoresistance -- the TMR Effect

Directory:Solid State

There was an error working with the wiki: Code[7]

Directory:Toroidal Power

Directory:Marko Rodin Coil / Torus / Motor

Directory:Power from Ambient Electromagnetic Radiation

Directory:Gravity Motors


There was an error working with the wiki: Code[8]

- Directory