Directory:Bedini SG:Data

Lasted edited by Andrew Munsey, updated on June 14, 2016 at 9:14 pm.

Edit wiki on beta.pesn.com

7 errors has been found on this page. Administrator will correct this soon.
This page has been imported from the old peswiki website. This message will be removed once updated.

You are here: PES Network > Main Page > Directory:Bedini SG > Data

----

'Data Report for John Bedini's Directory:Bedini SG'

Contents

1:

Data
2:

See also

Data

Most data is being published under the individual Directory:Bedini SG:Replications pages.

Reports

See also the Directory:Bedini SG:Replications.

Directory:Bedini SG:Replications:PES:Sterling Allan:Data:Exp21 Load Test Solid State - Solid state charge works better than rotational charge at the same charging current. For the spinning rotor scenario, I implemented most of John Bedini's recent suggestions. Neither test reveals over unity, though the solid state test looked at first like it was going to. 17 pp of data posted. (Dec. 29 - Jan. 3)

Directory:Bedini SG:Replications:PES:Sterling Allan:Data:Exp18 Load Test - Output was ~85% of input. The difference can be ascribed to what is required to keep the motor wheel in motion. (Dec. 20-23)

Directory:Bedini SG:Replications:PES:Sterling Allan:Data:Exp13 Continuous Rotation of Conditioned Batteries - Rotating ten 6V batteries connected 2x 6v into five quasi 12-Vs, taking turns on input side. Running from Nov. 22 to 27, 2004, the average voltage level of the set gradually dropped from 6.598 to 6.413.

Directory:Bedini SG:Replications:Gerhard Flemming - 12v that have been supercharged, rotated one at a time through the front end (input) show a gradual collective decline in charge over time. [Note, Peter/John recommended 5, four for the back side.]

Directory:Bedini SG:Replications:PES:Sterling Allan:Data:Exp12.1-3 Same Output Three Different Input Scenarios - Each schenario delivered 0.040 amps +/- .001 to the receiving battery. One scenario entailed the wheel rotating at nearly twice the speed as another scenario. A third scenario entailed a large variation in the gap between the wheel and the coil. Battery charged a nominally the same rate each time.

Image:Gap Influence in Bedini SG SDA Exp11 thumbnail.jpg

Directory:Bedini SG:Replications:PES:Sterling Allan:Data:Exp11 Gap Distance (Nov. 15,16 data)

Directory:Bedini SG:Replications:PES:Sterling Allan:Data:Exp10.4 Different Standing Discharge Rates - Batteries longest on the Bedini Circuit discharged significantly more slowly at first, but then after a day discharged to a lower voltage than those batteries that are more recent to the circuit and lower than one that was damaged early on, and dropped rapidly at first.

Image:Ohms v Amps v RPM SDA Bedini SG Exp10 thumbnail.gif

Directory:Bedini SG:Replications:PES:Sterling Allan:Data:Exp10.2 Ohms v Amps v RPM Chart - data shows several regions in which two stable rotation speeds are obtained at the same resistance in the Bedini SG circuit. Looking for ideal resistance for running the motor-energizer.

Directory:Bedini SG:Replications:PES:Sterling Allan:Data:Exp9 Zero Current Charge - Resistor set to 20.8k ohms where the input current is 0.00_ amps, and the output current is theoretically zero as determined by extrapolation of a linear curve drawn from data taken at 0.035, 0.025, 0.015, and 0.005 amps output. Results show no change in battery. (Oct. 29 through Nov. 3, 2004)

Directory:Bedini SG:Replications:PES:Sterling Allan:Data:Exp8 Load Test - Using West Mountain Radio Computerized Battery Analyzer (CBA) from PowerWerx.com. (Oct. 26, 2004)

Image:SDA Bedini SG solid state Ohms v Amps two voltage levels two curves 041024 140.gif

Directory:Bedini SG:Replications:PES:Sterling Allan:Data:Exp6 - Experiment to (1) determine the window where solid state (no wheel rotation, but circuit activation by resonance) can take place (2) supercharge more batteries, seeking optimal solid state charge profile in process. (Oct. 22,23, 2004)

Directory:Bedini SG:Replications:PES:Sterling Allan:Data:Exp6:Charts Graphing ohms versus amps. Includes discovery of "zero charge" output point.

Directory:Bedini SG:Replications:PES:Sterling Allan:Data:Exp5 - Found in process of running an experiement on various resistances versus amps and rpm. (Oct. 19, 2004)

Image:SDA rep data exp1 Bedini SG close left 111.gif

There was an error working with the wiki: Code[1] - Multiple batteries being charged at the same time tend toward the same voltage. Input voltage seen by the output batteries. Input batteries upon rotation recoil to an extrapolated line.

Directory:Bedini SG:Replications:PES:Sterling Allan:Data:Exp1 Switching in out - Test ran for 100 hours using the same two 6V batteries then was terminated as batteries were too low to continue. (Oct. 9-12, 2004)

Directory:Bedini SG:Data:RPM v Amps - shows a linear relationship between rpm and amps. Double speed of rotor = double amps being drawn from battery (note that this worked because the battery being used was weak enough to not sustain its natural rpm). (Oct. 9, 2004)

Observations

School Girl motor has to be kick-started. (Other Bedini circuit designs are self-starting his designs also include solid state iterations.)

Increased load on motor draws less amperage from the input battery.

The device is not a torque-producing motor but readily runs down when extra load is added.

Claim (not proven [actually disproven by the numerous tests run in this project]): the output radiant energy is not picked up by regular instrumentation in the form of increased output current, but the increased charge in the battery does signal the existence of the energy.

(not documented)The magnet strength is essentially irrelevant to producing the radiant effect in the coil.

(claim, not proven that I know of) Radiant energy does not require conducting materials to flow, but can travel outside the plastic sheath of conduit.

Replications

Directory:Bedini SG:Replications - Listing of people who are in process of replicating or who have successfully replicated the device. An index page for each investigator, and a page for each device, with sub-pages for data reports.