PESWiki.com -- Pure Energy Systems Wiki: Finding and facilitating breakthrough clean energy technologies.

Directory:ERR Fluxgenerator by Noah's Ark Research Foundation

From PESWiki

Page first featured August 15, 2009

Dr. James Schwartz lights up three 800-Watt bulbs with his solid state aluminum-bismuth panel system.

Electromagnet Flux Energy Research

Inventor, James B. Schwartz of the Philippines, has come up with a device that allegedly puts out as much as six kilowatts of electricity, tying into the Earth's frequencies, using a solid state arrangement in a panel made from "left-handed material" -- Aluminum and Bismuth interwoven with coils.

He's presently in process of testing and refining the design.

"I consider this one of the most promising designs and groups for bringing forward a working device that will provide clean energy 24/7/365." -- Sterling D. Allan; Nov. 23, 2009

About

Official Website

http://www.freewebs.com/narfschwartz/

Interviews

On Aug. 15, 2009, Sterling D. Allan extended an invitation to Dr. Schwartz to come on the Free Energy Now radio show.

an interview with James Ben Schwartz with Bill Alek - Dec 13, 2008

Videos

ERR Fluxgenerator selfrunning 3 KW Free Energy generator

ERR Fluxgenerator selfrunning 3 KW Free Energy generator (YouTube backup by overunitydotcom; July 26, 2009)
To all our members - Dr. Schwartz comments on the video on his forum. "The proof of concept video that Stefan posted up is relatively new, filmed just a few months ago, but the technology and principle of operation have been a matter of research for many years now. Others ahead of us have pioneered similar

technology, like Moray and Tesla, but as of yet none have perfected it to the point that others can use it. ... My research has had quite a few setbacks over the years and even now there are safety concerns associated with this type of device. Progress is being made and arrangements are in place to move toward the realization of genuine usable power production, but there are still steps ahead that must not be rushed to ensure the success of this technology." (Aug 8, 2009)

Dr. Schwartz explains in the video: "We have three plates here... [with] a solid piece of aluminum on one side, [followed by] a sheet of bismuth, [followed by] another aluminum plate with six cut-outs; you've got the coils in there; then you put another bismuth, another plate of coils on top of that, then another bismuth, then another solid plate, then you've got a panel. When we activate these with our activator, which causes the frequencies in these plates with alternating frequency, they produce electrons by agitating the bismuth and aluminum. We've got to ground it to the earth. That's what we're going to do here; and find the frequency of the earth that matches. It will seek out and find."

"It's designed as a 6,000 Watt system, but today we're only putting out about [~2,400] Watts. We've got three 800-Watt lights. The weight is approximately 42 pounds, and that's mostly the case. The plates and circuits boards are about 8 pounds."

Dr. Schwartz Free Energy Electromagnetic Generator

Its similar to Tom Beardens MEG except that it doesnt need an external power supply to switch the magnetic fields. It uses a very powerful magnet with a special circuit board that contains a new hi-tech chip to switch the magnetic fields. It also contains ultra-thin graphite sheets called graphene. Using a very sensitive technique, we were able to separate the individual sheets of carbon atoms that are layered on top of one another in graphite. These layers are electrically conducting because they contain electrons that are free to roam across each layer. In the graphene, the charge carrying particles act as if they're without mass, or weight. In this respect theyre more like photon particles that convey light than like electrons. (YouTube backup by overunitydotcom; July 28, 2009)

Information Sheet about ERR

On July 28, 2009, Stefan Hartman posted the following from Dr. Schwartz:

For many years I have been experimenting with new materials that support electromagnetic wave propagation in ways that are not observed in nature. Other research teams around the world are doing similar experiments that also backup this theory. I have been able to create materials that support this type of effect for light and other electromagnetic waves. Even some physicists are starting to challenge what was thought to be the basic laws of nature. Many of the hard-nosed skeptics are finding it increasingly more difficult to disprove the left-hand rule.

In nature, all materials seem to obey the right-hand rule. The fingers of the right hand represent the waves of the electric field, and when you curl the fingers around to the base of the hand, this represents the magnetic field ; the outstretched thumb indicates the direction of the flow of power

Back in 1968 a Russian theorist; V.G. Veselago had predicted that new materials could be engineered to interact with our environment, which is just the opposite of how natural materials react. In 2000, researchers at the University of California-San Diego (UCSD) confirmed this, creating what's known as the first "left-handed" material. A special team at UCSD created material that caused fields to move to the left even though the electromagnetic energy moved to the right. The light waves produced in this material also produced an inverted Doppler effect. Researchers at MIT and the University of Delaware, is also exploring left-handed media.

We are now discovering that the things we held to be inviolable can in fact, be violated under certain conditions. Many research teams are already able to build structures that support this theory.

Much of my research over the past 17 years has proved that these new kinds of materials can cause different affects when it comes to magnetic fields. I’m already using left-handed material in my ERR (Electromagnetic Radiation Receiver) experiments. I’ve proven this theory with my ERR prototype. Lawrence Rayburn a researcher of electromagnetic fields has also proved this theory with his left-hand wound coils. Even though some of us have proven the left-hand theory, no one seems to want to admit that we have disproved one of the sacred laws of nature.

You’ll find the drawing of my special experimental Flux Power Station in the Noah’s Ark Research Foundation folder in photos.. A special frequency generator is used to induce a series of alternating frequencies to create a flow of electrons when activating the magnetic flux field. This theory is still in the experimental stages so I still have a lot of research and testing for safety and other factors.

The secret is in the material used, the size of the wire and the number of turns plus the frequency and how you alternate that frequency. There are many combinations that will allow you to get small amounts of electrons to flow.

I finished a simple set of drawings for my first 160,000 watt power station. I don’t want to release my blueprints because it might fall into the wrong hands. These simple drawings and information is not enough for other research organizations to copy our technology.

We still need to build the first prototype and test it over a period of time to make sure it’s safe and to fix any bugs that we might find. The smaller model worked very well but we don’t know how the bigger one will work until it’s built and tested.

This ERR Flux Power Station is designed to run a large house or you can add more Flux Power Vaults which is 10,000 watts or more each if you need more power. It can even be built big enough for a factory or a whole community of houses.

I’ve already started building the first prototype in the basement of our house in the Philippines. My crew has already poured the cement for the chambers. The copper and fiberglass tracks with all the electrical contacts where the Flux Plates slide into place are being built in our machine shop. After the chambers are finished and the cement is cured the tracks will be bolted into place. The cement work will take about two weeks to finish the 16 chambers. By then the first 10 tracks will be ready to install. Each Flux Power Plate as it’s finished will be slid into place and tested to make sure it’s making proper contact. After all 10 Flux Power Plates have been slid into place and tested we can bolt the airtight chamber vault door into place. Then we will be ready to test the o-rings with a vacuum pump. After the chamber has passed the vacuum test we can pressure-rise the chamber to 1.5 psi with a special gas. Then the first chamber will be ready to go on line producing 10 to 18,000 Watts DC power. The reason we’re not sure of the exact output is because we are developing new left-handed materials that could possible increase the output by as much as eight times. As each new chamber comes on line I can disassemble my older smaller ERR units. My older ERR units have become more bothersome and costly to maintain over the years.

The new Flux Power Plates should be maintenance free for many years (I hope). As we develop newer and better Power Plates the older Plates can be easily replaced by shutting down one chamber at a time.

After the frequency generator is shut down going to that chamber then the cover can be removed exposing the plates. If the new Flux Power Plates are the same thickness then the old plates are simply slid out and the new plates slid into place. If the new plates are thicker or thinner then the tracks will need to be replaced. After replacing the plates the o-rings on the vault door is replaced and the cover is bolted back on. The chamber will be vacuum tested and if no leaks are found then the chamber can be pressure-rised to 1.5 psi with a special gas and the frequency generator can be turned on. After output is tested the chamber is ready to be added to the power station.

Drawing # 1 shows the chambers without the airtight covers. The chamber holds ten Flux Power Plates that are 48” X 48” X 4” which can produce 1,000 to as high 8,000 watts each depending on the Plates. As we design newer left-handed materials that support electromagnetic wave propagation we will be able to increase the power output. Each chamber is designed with special slots and electrical connectors to connect to the Flux Power Plates when they are slid into position in the chamber. The reason for individual chambers is so that the whole system need not be shut down in case of a Flux Plate burn out. One chamber can be shut down to replace one or more burnt Plates without shutting down the whole Power Station. It also shows the frequency and power lines. The lines coming from the frequency generator going into the chamber and the heavy DC output lines use the same sealed system.

Drawing #2 is basically the same as #1except it shows the gas lines going to each chamber and it has the covers bolted into place. Each vault has an airtight cement cover to seal the chamber so that we can extract all the air and fill the chamber with a special gas at a pressure of 1.5 psi. These covers with their o-ring seals are very important so that no air can leak into the chamber. Any oxygen in the chamber can cause flash burns between the plates. It also shows the electrical lines going from each vault to the main power box.

Drawing #3 shows a front and side view of the Flux Power Plates.

Drawing #4 shows one of the inner aluminium plates which is different from the two outer solid aluminum plates. Each of these inner plates has 144 slots that are cut to 10 ½ X 2 ½ cm where 144 special coils are inserted.

Drawing #5 is a close up of the ten Flux Power Plates and the tracks.

Independent Testing

list here

Witnessed by Harvey

On Jul 30, 2009, Harvey wrote

"I feel privileged that Dr. Schwartz afforded me the rare opportunity of actually seeing the device operate in person. A few months back, shortly after the demonstration video was made, I was notified that Dr. Schwartz was within driving distance and was willing to demonstrate the ERR for me. My wife and I enjoyed the trip and she is still amazed at what we saw. I couldn't stop thinking about it. I was full of questions and Dr. Schwartz graciously answered all those he was able to share without infringing on prior agreements. He told me at that time that we need to proceed slowly as research and development continue and some of the safety issues are addressed."

Patents

list here

Profiles

Company: Noah's Ark Research Foundation

"We are planning to move our Noah’s Ark Research facility of Japan to Arizona where we will be joining the new Ranch Project of Bill Alek. We are also planning to put Noah’s Ark Research facilities in India and the Fiji Islands." [1]

Partner Company: New Ark Power

Dan Santle(sp?), introduces Dr. Schwartz in the above video.

Inventor: Dr. James B. Schwartz

Coverage

Latest

Sept 27, 1976

Noah’s Ark Research Foundation was formed

In the News

Google News > ERR Flux Generator - null as of Aug. 15, 2009.

Featured: Electromagnetic > ERR Fluxgenerator >
Update on Schwartz' ERR Fluxgenerator - More information regarding the revolutionary, solid state generator based on a combination of "left-hand materials" that somehow harness energy freely from the environment. The inventor is not looking for investment money. (PESN; Sept. 4, 2009) (Comments)

Featured: Electromagnetic / Solid State >
ERR Fluxgenerator by Noah's Ark Research Foundation - Inventor, James B. Schwartz of the Philippines, has come up with a device that allegedly puts out six kilowatts of electricity from the surroundings, using a solid state arrangement in a panel made from "left-handed material" -- Aluminum and Bismuth interwoven with coils -- tying into the Earth's frequencies. (PESWiki; Aug. 15, 2009)

Other Coverage

Selfrunning 3 KWatts ERR unit powering 3 x 800 Watt lamps - (OverUnity.com; July 27, 2009)
http://oriharu.net/jgene.htm#ERR

Comments

See Discussion page

http://tech.groups.yahoo.com/group/noahsarkenergyresearch - Mr. Schwartz´s yahoogroup

Related Technologies

Directory:Elemental Rod Generator - An earlier version by Dr. Schwartz

On Aug 8, 2009, Dr. Schwartz wrote

"Some have expressed the desire to jump in and start experimenting with what they can. That's encouraging, because you never know when someone else may come up with new applications or ways to do things. There are so many projects that our group wants to get involved with and the ERR is just one single thing in a whole array of directions ahead of us.

"I truly wish I could share 100% of everything I know right now, but I have obligations that prohibit it. I would like at least get others thinking about how energy moves inside materials and what that means as to how we get energy in and out of those materials. Here are a few links to just get your feet wet with some ideas that are not normally on the general learning list. Remember that light is electromagnetic radiation.

http://physics.ucsd.edu/lhmedia/whatis.html (note that Dr. Smith is with Duke University and the link on that page is old,

the new one is below)

Application essay

"This information along with what I have already provided regarding fluxing a magnetic field may be enough to get you pointed toward some minor experiments without my violating any agreements. Please be safe in your work, as sometimes unexpected things happen and probably will. It is our hope that as things mature, we can hand this technology over to all that wish to put it to use. In the mean time, put this group to good use - there are a lot of good thinkers here that can collaborate and get things accomplished. Feel free to share your ideas - even a stopped clock is right twice a day!"

Contact

Dr. James B. Schwartz
email: narf1933@yahoo.com