PesWiki.com

Menu

Directory:Bedini SG:Replications:PES:Sterling Allan:Data

Lasted edited by Andrew Munsey, updated on June 14, 2016 at 8:43 pm.

  • 12 errors has been found on this page. Administrator will correct this soon.
  • This page has been imported from the old peswiki website. This message will be removed once updated.

You are here: PES Network > Main Page > There was an error working with the wiki: Code[1] > Directory:Bedini SG:Replications > Directory:Bedini SG:Replications:PES > Directory:Bedini SG:Replications:PES:Sterling Allan > Data

----

Image:SDA repl Bedini SG b 90.jpg

'Data from Sterling D. Allan's Directory:Bedini SG:Replications:PES:Sterling Allan of John Bedini's Directory:Bedini SG'

Synopsis

I do not believe that I ever achieved a situation in which I was harnessing unseen energy external to the system. All my data support an internal charge-discharge scenario, with a net loss due to system inefficiencies.

I did observe a number of very fascinating phenomena. Though driven by an expectation for success that ended up not being met, I will say that the experience was worth while. The quest was enjoyable, though very frustrating as well.

Batteries are a very tricking thing to work with.

You need to take into consideration the charge/discharge curve characteristics.

A discharged battery voltage will rise very rapidly with very little loss of voltage from a fully-charged battery.

-- Congress:Founder:Sterling D. Allan (Jan. 21, 2007)

Sterling's Data

Directory:Bedini SG:Replications:PES:Sterling Allan:Data:Exp21 Load Test Solid State - Solid state charge works better than rotational charge at the same charging current. For the spinning rotor scenario, I implemented most of John Bedini's recent suggestions. Neither test reveals over unity, though the solid state test looked at first like it was going to. 17 pp of data posted. (Dec. 29 - Jan. 3)

Image:DavidAllan balances 1egg a.jpg

Directory:Bedini SG:Replications:PES:Sterling Allan:Data:Exp20.1 Balancing the Egg - reports a phenomenon in which a quasi-steady balance point is attained between solid state resonance and the first rotation speed. At that point, the meter jumps all over the place. (Dec. 29)

Directory:Bedini SG:Replications:PES:Sterling Allan:Data:Exp19 new coil and wheel - Changed wheel from 22" diam 16 magnets to 16.5" diam 24 magnets. Changed coil from ~425 turns to ~1290 turns. New wheel spins faster on old coil, stabilizes more rapidly on new coil. Data compared.

Directory:Bedini SG:Replications:PES:Sterling Allan:Data:Exp18 Load Test - Though output was less than input, the amount of energy required to keep the motor wheel in motion during charge bespeaks the tapping of radiant energy. (Dec. 20-23)

Image:Bedini SG by SDA Exp17 Dec17 2004 101.jpg

There was an error working with the wiki: Code[2] - Continual rotation of conditioned batteries from the back to the front to the back, etc, sees four consecutive increases in battery capacity in 48 hours. Subsequent data explains. Commenced Dec. 10 terminated Dec. 18, 2004.

Brief update of my recent experimentation - Thumbnail sketch of three reports pending.

Exp. 16: Testing various household battery types, rechargeable and non-rechargeable to see how they perform with the Bedini SG charge.

Directory:Bedini SG:Replications:PES:Sterling Allan:Data:Exp16:D-Size Rechargeable NiCd - A baby swing ran 1.43 times longer after the second charge of four NiCd D-size batteries.

Directory:Bedini SG:Replications:PES:Sterling Allan:Data:Exp16.13:RayovacAA Alkaline - Four non-rechargeable Alkaline AA Batteries by Rayovac took a charge from the Bedini SG but then did not perform under load.

Exp. 15: Deceleration Data - to calculate rough estimate of energy required to keep wheel rotating. Nov. 29

Exp. 14: Recharing the batteries. Individually supercharged each of the batteries again. Nov. 29 - Dec. 3, 2004.

Image:SDA Bedini SG Exp14 Exp13 Average Voltages thumb.gif
Directory:Bedini SG:Replications:PES:Sterling Allan:Data:Exp14.2 Steady State Discharging - Compares Steady State Discharge with Average Voltage Drop During Continuous Rotation of Conditioned Batteries. Dec. 3-10.
Image:SDA Bedini SG Exp13 Rotating Conditioned Batts thumb.gif

Directory:Bedini SG:Replications:PES:Sterling Allan:Data:Exp13 Continuous Rotation of Conditioned Batteries - Rotating ten 6V batteries connected 2x 6v into five quasi 12-Vs, taking turns on input side. Running from Nov. 22 to 28, 2004, the average voltage level of the entire set gradually dropped from 6.598 to 6.413.

Directory:Bedini SG:Replications:PES:Sterling Allan:Data:Exp12.1-3 Same Output Three Different Input Scenarios - Each schenario delivered 0.040 amps +/- .001 to the receiving battery. One scenario entailed the wheel rotating at nearly twice the speed as another scenario. A third scenario entailed a large variation in the gap between the wheel and the coil. Battery charged a nominally the same rate each time.

Image:Gap Influence in Bedini SG SDA Exp11 thumbnail.jpg

Directory:Bedini SG:Replications:PES:Sterling Allan:Data:Exp11 Gap Distance - Exp. 11 by SDA shows that the closest distance does not produce optimum RPM. (Nov. 15,16 data)

Directory:Bedini SG:Replications:PES:Sterling Allan:Data:Exp10 - in order to begin the rotation scenario (taking turns moving one from back side to front side). Batteries are in various stages of exposure to Bedini circuit. Four have been supercharged previously.

Image:Ohms v Amps v RPM SDA Bedini SG Exp10 thumbnail.gif
Directory:Bedini SG:Replications:PES:Sterling Allan:Data:Exp10.2 Ohms v Amps v RPM Chart - Sterling's Bedini SG data shows several regions in which two stable rotation speeds are obtained at the same resistance in the Bedini SG circuit. Looking for ideal resistance for running the motor-energizer.
Image:Sitting Discharge Variations SDA Bedini SG Exp10p4 thumb.gif
Directory:Bedini SG:Replications:PES:Sterling Allan:Data:Exp10.4 Different Standing Discharge Rates - Batteries longest on the Bedini Circuit discharged significantly more slowly at first, but then after a day discharged to a lower voltage than those batteries that are more recent to the circuit and lower than one that was damaged early on, and dropped rapidly at first.

Directory:Bedini SG:Replications:PES:Sterling Allan:Data:Exp9 Zero Current Charge - Resistor set to 20.8k ohms where the input current is 0.00_ amps, and the output current is theoretically zero as determined by extrapolation of a linear curve drawn from data taken at 0.035, 0.025, 0.015, and 0.005 amps output. Results show no change in battery. (Oct. 29 through Nov. 3, 2004)

Directory:Bedini SG:Replications:PES:Sterling Allan:Data:Exp8 Load Test - Using West Mountain Radio Computerized Battery Analyzer (CBA) from PowerWerx.com. (Oct. 26, 2004)

Directory:Bedini SG:Replications:PES:Sterling Allan:Data:Exp8 Load Test - Battery 7 is factory new, while Battery has been all over the Bedini circuit (input, output many times, series, parallel, supercharged, solid state). Very unusual graph emerges of battery 2's performance next to battery 7. 'Bedini-SG-conditioned Battery 2 holds its charge better than factory-new battery 7.'

Directory:Bedini SG:Replications:PES:Sterling Allan:Data:Exp8 Load Test - Battery 5 started later, and was only "solid state" (no moving parts) charged, including the "no current" charge. Battery 2 held its charge better than Battery 5, possibly because it has spent more time being conditioned in the Bedini circuit though I expect that the "no current" charge will prove to be more robust all other things held the same.

There was an error working with the wiki: Code[3] - Based on data collected in Exp. 6, which showed that output battery amperage versus ohms resistance forms a linear graph between 2k and 10k ohms where it goes to zero, while input amps creates an asmyptotic curve. Resistance for test set at 17.49 ohms. Output battery charge increased slightly and held firm, while control batteries dropped. (Oct. 24, 25, 2004)

Image:SDA Bedini SG solid state Ohms v Amps two voltage levels two curves 041024 140.gif

Directory:Bedini SG:Replications:PES:Sterling Allan:Data:Exp6 - Experiment to (1) determine the window where solid state (no wheel rotation, but circuit activation by resonance) can take place (2) supercharge more batteries, seeking optimal solid state charge profile in process. (Oct. 22,23, 2004)

Directory:Bedini SG:Replications:PES:Sterling Allan:Data:Exp6:Charts Graphing ohms versus amps. Includes discovery of "zero charge" output point.

Directory:Bedini SG:Replications:PES:Sterling Allan:Data:Exp5 - Found in process of running an experiement on various resistances versus amps and rpm. (Oct. 19, 2004)

Directory:Bedini SG:Replications:PES:Sterling Allan:Data:Exp4 -- Two 6V in series (12V) gave 0.32 amps input, 0.10 amps output. Used 12-volt 2-amp trickle charger on input Batteries 1,2. (Oct. 15-17, 2004)

There was an error working with the wiki: Code[4] -- I blew three transistors when trying to hook up this circuit. Melted the plastic off one of my wires. Peter says I need more wraps on my coil to have more inductance to match the impedance of the larger battery. (Oct. 14, 15, 2004)

There was an error working with the wiki: Code[5] - Two 6V in series (12V) gave 0.32 amps input, 0.10 amps output. Used 12-volt 2-amp trickle charger on input Batteries 1,2. (Oct. 14, 2004)

Image:SDA rep data exp1 Bedini SG close left 111.gif

Directory:Bedini SG:Replications:PES:Sterling Allan:Data:Exp1 Switching in out - Test ran for 100 hours using the same two 6V batteries then terminated due to new information about the nature of batteries. (Oct. 9-12, 2004)

Directory:Bedini SG:Calculations:Deceleration - data collected, tabulation pending. To approximate the resistances of the wheel rotation. Did decelartion in Exp. 1 and Exp __.

Directory:Bedini SG:Data:RPM v Amps - first data I collected shows a linear relationship between rpm and maps. Double speed of rotor = double amps being drawn from battery (note that this worked because the battery being used was weak enough to not sustain its natural rpm). (Oct. 9, 2004)

Note about Trickle Charger

Nov. 20, 2004

I'm noticing a high degree of stability, reproducibility, and predictability in using the IntelTender Model 150-6 from DigiKey with my 6v Panasonic (LC-R064R2P) 4.2Ah input batteries.

By keeping the trickle charger on, the input voltage is highly stable, making for more rigorous science because that is one less variable in the mix.

As I'm supercharging my batteries one at a time (recommended, rather than in sets, because of the varying characteristics of individual batteries), I see the same input voltage per given voltage of the output battery. Off the top of my head, without actually running the numbers, I would estimate that it is +/- 0.005 volts consistent. It is very good.

The only caveat to this is that between batteries, when the circuit is disconnected, the input batteries, still on trickle, will jump up in voltage, so when re-connected to the circuit, it will take 15-30 minutes for them to equilibrate back to a consistent level.

Another consistency that arises in this set-up is input/output current. It, also, is a function of input voltage level and output voltage level, other factors (resistance, etc.) being the same.

I've seen it reproduced over and over as I'm supercharging one battery after another using the same parameters.

Sterling

See also

Directory:Bedini SG:Replications:PES:Sterling Allan - index

Directory:Bedini SG:Data - General Bedini SG

Directory:Bedini SG:Replications - general index

- Directory:Bedini SG

- Directory

- Main Page

There was an error working with the wiki: Code[6]

There was an error working with the wiki: Code[7]

There was an error working with the wiki: Code[8]

There was an error working with the wiki: Code[9]

There was an error working with the wiki: Code[10]

There was an error working with the wiki: Code[11]

There was an error working with the wiki: Code[12]

Comments